Manual Transmission Exam 2 Practice

These questions are part of the practice quiz. Start practicing

• What occurs when a five-speed transmission is in third gear?
• What does a transmission control module NOT do?
• What was one of the earliest front wheel drive vehicles?
• What is one significant advantage of overdrive for a vehicle?
• What is the primary cause of clutch fade?
• During gear changes, what can help ensure a smoother transition?
• Which technician is correct regarding the causes of excessive shift effort during the dynamic shift test?
• When servicing a drive axle, Technician A says that it's a good idea to tape the U-joint caps to prevent them from coming off. Technician B says that needle bearings are used with these type U-joints. Which technician is correct?
• In what scenario would you expect to find a transmission failure?
• What is a key advantage of smooth clutch engagement when driving a manual transmission?
• The main shaft of a transmission is also known as what?
• What is the purpose of the spline shape in a transmission?
• What is a common symptom of a worn throw-out bearing?
• What is the correct way to engage the parking brake in a manual vehicle?
• Which type of joint is the most commonly used outer joint on FWD vehicles?
• How does the alignment of a vehicle's driveshaft impact manual transmission operation?
• Which of these could cause U-joint angles to change from their normal angles?
• What method is commonly used to adjust the bearing on many transaxle input shafts?
• What is the function of a reverse lockout mechanism in manual transmissions?
• What can excessive slippage of the clutch result in?
• Which statement best describes the main benefit of using a manual transmission?
• The detent mechanism inside a transmission is used to perform which function?
• What might be a consequence of not taping U-joint caps during installation?
• Which type of bearings are commonly used in manual transmissions?
• What is the primary benefit of learning to "feather" the clutch in a manual transmission vehicle?
• What does improper transmission fluid maintenance typically lead to?
• Which maintenance task is essential for a manual transmission?
• The last step after replacing a defective CV boot is to ________.
• Two technicians are discussing U-joints. Technician A says that a defective U-joint could cause a loud clunk when the transmission is shifted between Drive and Reverse. Technician B says a worn U-joint can cause a clicking sound when driving the vehicle in reverse. Which technician is correct?
• What is the function of the flywheel in a manual transmission?
• With the engine running and the transmission in neutral with the clutch engaged, which of the following components is NOT rotating?
• In which gear would you typically find maximum engine power for acceleration?
• Which type of gears are used for reverse in most transaxles?
• When checking a transaxle's lubricant, where should the fluid level be?
• What maintenance task should be conducted to ensure the clutch system is functioning correctly?
• What does the neutral position do in a manual transmission?
• Which gear is most likely to use a spur gear in a manual transmission?
• What is the function of the pilot bearing in a manual transmission?
• The cluster gear is supported by which of the following?
• What is the main reason for using helical-cut gears in a transaxle?
• What should you do to maintain safety when driving a manual vehicle in heavy traffic?
• What is the necessary action when shifting gears to prevent grinding?
• What does “double clutching” involve?
• What is a common indication of a worn CV joint?
• What symptom commonly indicates problems with a driveshaft in a front-wheel drive vehicle?
• What is the most likely cause of a rear-wheel drive vehicle shuddering or vibrating when starting from a stop?
• What type of joint is typically used in the rear axle of four-wheel-drive vehicles?
• Are all drive shafts balanced?
• The splines of the drive shaft yoke should be lubricated to prevent ________.
• The final drive ring and pinion gears in a typical transaxle utilize which type?
• What is the main function of the differential pinion gears in a transaxle?
• Which type of bearing usually requires preloading in a transaxle?
• What should be checked if there are issues with clutch engagement?
• How does proper clutch use affect manual transmission performance?
• What components are typically found in a transaxle repair kit?
• What is a sign that the clutch plate may be worn out?
• Why is it important to check the fluid levels in a manual transmission?
• Which of the following is a typical cause of manual transmission failure?
• Two technicians are discussing a transmission that is noisy in first, second, third, and reverse but quiet in fourth gear. Which technician is correct regarding the likely cause?
• Why is proper clutch engagement essential during takeoff?
• What is a critical consequence of engine stalling during takeoff in manual vehicles?
• When replacing a CV joint boot, what must always be inspected?
• What impact does downshifting have on vehicle performance?
• What is an acceptable adjustment method to correct the end play in a tapered roller bearing transmission?
• What is likely causing a noisy transmission when driving?
• In a transaxle, the synchronizer assemblies are mounted on which component?
• What is a consequence of riding the clutch?
• How is the end play in a transmission with tapered roller bearings adjusted?
• What could be a consequence of forced downshifting?
• A defective outer CV joint will usually make a ________.
• What can lead to smoother low-speed maneuvers in a manual vehicle?
• What type of outer CV joints are used on front-wheel drive vehicles?
• A transmission is lubricated primarily to achieve which purpose?
• Transaxle cases are typically made from which material?
• Two technicians are discussing a transaxle's differential. Which technician's statement is correct?
• How can smooth driving habits affect the longevity of a manual transmission?
• What impact does reduced weight in a manual transmission have?
• What does the term "creep" refer to in manual transmission vehicles?
• Why is it crucial to follow the manufacturer's specifications for fluid and maintenance in manual transmissions?
• What is used in a manual transmission to achieve a clash-free shift, preventing grinding sounds?
• How can cold temperatures affect the operation of a manual transmission?
• Which component of a transaxle is directly connected to the clutch disc?
• Which component can limit the flexibility of the driveshaft?
• What is the purpose of synchronizers in manual transmissions?
• Which of the following is NOT a step in checking bearings?
• What is commonly prevented by a reverse lockout mechanism in manual vehicles?
• Which condition is NOT typically associated with low transmission fluid?
• What role does transmission fluid play in a manual transmission?
• How does a manual transmission generally compare to an automatic in terms of fuel efficiency?
• When is the clutch considered fully engaged?
• What is the primary advantage of a short throw shifter?
• What does "stall speed" refer to in manual transmissions?
• In a manual transmission system, which component delivers power to the drive wheels?
• What issue might arise from using gear oil that is too thin?
• In a vehicle with a transaxle, what is primarily affected by the lubrication system?
• FWD driveshaft problems are usually indicated by ________.
• What is the maximum allowable difference between front and rear working angles of a drive shaft?
• How are tapered roller bearings generally adjusted within a transaxle?
• What does the term "spline" refer to in the context of transmissions?
• What is the function of the shifter in a manual transmission?
• Which component is crucial for the prevention of gear clash during shifting?
• What may occur if gears are shifted without pressing the clutch?
• During a typical upshift, the synchronizer must perform which action?
• Which habit can lead to a more comfortable driving experience in a manual vehicle?
• What type of oils are generally recommended for use in manual transmissions?
• Why is it important to match engine RPM and transmission speed during shifting?
• Which of the following is NOT used as CV joint boot material?
• A four-speed transmission is making a grinding noise only while shifting into second gear. What could this be caused by?
• If the gear shifter feels "notchy", what might be the issue?
• What does the term “gear ratio” refer to in manual transmissions?
• What component is often the cause of excessive shifting effort?
• Technician A says that carbon fiber driveshafts need support bearings every 24 inches. Technician B says that carbon fiber and aluminum driveshafts reduce rotating mass and are more efficient than steel driveshafts. Which technician is correct?
• What does it mean to "stall" a manual transmission vehicle?
• What is the primary purpose of lubricating the splines of a drive shaft yoke?
• Why is it important to check the specified fluid type before inspecting a transmission?
• What technique can be used to smoothly start moving from a stop on an incline?
• Which of the following is a poor practice regarding manual transmission fluid?
• Torque steer in vehicles can be attributed to which of the following?
• If your vehicle stalls on an incline, what is the first step you should take?
• How can blocker ring clearance be appropriately checked?
• What may indicate that the transmission is slipping out of gear?
• What is the role of a shift fork in a manual transmission?
• Most manual transmissions use a case made from which material?
• What is the consequence of over-revving an engine in a manual transmission vehicle?
• What typically drives the speedometer gear?
• Which test is best for isolating clutch system problems?
• In manual transmission vehicles, which process is essential for smooth shifting?
• Which of the following factors can cause torque steer?
• Most transaxles primarily use which type of gears?
• What needs to be removed to replace a drive axle shaft from a front wheel drive vehicle?
• How is preload in a bearing typically measured?
• Why is it important to maintain a safe following distance when driving a manual vehicle?
• What could occur if a driver fails to feather the clutch properly?
• What is the primary function of CV joints in a vehicle?
• What does a short throw shifter improve in a manual transmission?
• Which of the following is a sign of a failing manual transmission?
• When installing a bearing over a shaft, where should force be applied?
• What is the role of the clutch in a manual transmission?
• The lubricant used in a manual transmission can vary. Which of the following is correct?
• When is it best to use engine braking?
• A dent in an axle shaft can cause damage that may result in failure when engine torque is applied. True or False?
• What role does the transmission control module play in vehicles with automatic manual transmissions?
• In the context of torque steer on a front wheel-drive vehicle, what helps to reduce it?
• What distinguishes a synchronized transmission from an unsynchronized transmission?
• What is the first step in downshifting before a turn?
• What is the primary purpose of a manual transmission?
• What is essential for proper operation of tapered roller bearings in a transaxle?
• When shifting a transaxle while the engine is running, what problem might occur?
• Regarding synchronizer rings, which technician's statement is correct?
• The main purpose of a reverse lockout feature is to enhance what aspect of driving?
• What distinguishes a transaxle from a standard transmission?
• What could cause noticeable vibration less at high speeds in a rear-wheel drive vehicle?
• What purpose does the intermediate drive shaft serve in certain front wheel drive vehicles?
• Why is it important to avoid riding the clutch?
• What is the primary function of the main drive gear in a manual transmission?
• What is the primary role of synchronizers in a manual transmission?
• A defective (collapsed) engine mount on a front-wheel drive vehicle can cause a vibration. True or False?
• What does "rust dust" indicate in a transaxle system?
• In a manual transmission, the clutch disc must do what when engaged?
• When a five-speed transmission is in fourth gear, which statement is accurate?
• What type of lubrication is commonly used in most transaxles?
• How do modern manual transmissions differ from older designs?
• How can engine braking be beneficial while driving?
• What is the ideal RPM range for shifting up in a performance manual vehicle?
• What are the typical gear positions found in a 5-speed manual transmission?
• How is "gear ratio" defined in the context of manual transmissions?
• What is a good indicator that a manual vehicle may be experiencing transmission issues?
• Why might a driver prefer a well-maintained manual transmission?
• What does the clutch allow the driver to do during shifting?
• What must a driver do before downshifting in a manual transmission?
• Why might a transmission make noise in certain gears while being quiet in others?
• Excessive shift effort during testing is most likely influenced by which factor?
• What happens to engine performance if the manual transmission fluid levels are low?
• What might Technician A incorrectly suggest regarding a worn shift fork?
• What is the function of the clutch in a manual transmission system?
• What component is used to prevent accidental engagement of reverse while making an upshift?
• Which technician is correct regarding solutions to reduce torque steer?
• What is an important maintenance practice for prolonging manual transmission life?
• What are common symptoms of low transmission fluid in manual vehicles?
• What does "gear grinding" typically signify when shifting gears?
• Why is it not advisable to shift into reverse while moving forward in a manual vehicle?
• In a transaxle, which type of bearing is commonly used?
• What would be an outcome of worn countershaft bearings according to Technician B?
• Why should an impact wrench be avoided for installing drive axle shaft nuts?
• Drive axle shafts are also called ________.
• What can result from improper clutch use in a manual transmission vehicle?
• What tool is specifically used to check input shaft endplay?
• Two technicians are discussing a dented driveshaft. Technician A says that it should be repaired. Technician B says it should be replaced. Which technician is correct?
• Which statement is true regarding the components in a transaxle?
• When a five-speed transmission is in second gear, which statement is correct?
• What state is the engine in during a static shift test?
• What process might indicate a need for bearing replacement?
• What is a potential risk for beginner drivers learning to use a manual transmission?
• What type of gear can be found in the gear assembly of a manual transmission?
• What does a “collapsed” engine mount typically cause in a vehicle?
• The proper grease to use with CV joints is ________.
• Which noise during operation typically suggests a problem with a throw-out bearing?
• Before checking the fluid level in a manual transmission, what must a technician do?
• What can lead to a complete clutch failure?
• What is a potential result of late disengagement of the clutch while shifting?
• Which technician is correct regarding gear sizes in a transaxle?
• Which statement correctly describes the role of the input shaft in a manual transmission?
• Excessive shift effort during the static shift test could be caused by which of the following?
• Ensuring proper driveshaft alignment primarily benefits which aspect of the vehicle?
• Which approach is best for a technician to assess bearing wear?
• The synchronizer sleeve's role is to do what during a shift?
• It is recommended by many experts that an air impact wrench not be used to remove or install the drive axle shaft nut because the impacting force can damage the hub bearing. True or False?
• Incorrect or unequal U-joint working angles are most likely to be caused by ________.